Resin mixer, floppy doors & 3D printer grid

Last updated:

Need the green key card in Dahne’s Lab? Fixed nozzle order is 4 → 3 → 1 → 4. Floppy doors use partner dial targets. The 4×4 printer grid is random each run — copy the lit pattern; do not use a printed dead code.

Official We Were Here Tomorrow facility screenshot (R&D / lab context)
Official screenshot, Total Mayhem Games / Steam — facility / lab context. 待配官方截图: resin nozzles, floppy dials, 4×4 printer grid.

Official screenshot pending for this exact puzzle board — placeholder uses related facility art. Replace with Steam/Press Kit still when available.

Where this is

Chapter 2 · R&D / Dahne’s Laboratory stretch after the circuit board (community: Norček Facility early R&D). Miniature explorer works the cups/dials/plates; full-size partner reads recipes and cabinet lights.

Resin mixer — fixed nozzle order

Answer: nozzles 4 → 3 → 1 → 4 (Styrene → Acrylonitrile → Butadiene → Styrene). Multi-source: .net, Indie Walkthrough, weki Experimental Resin Notes.

Solution — resin steps
  1. Read the Experimental Resin Notes: equal Acrylonitrile + Butadiene, with Styrene before and after.
  2. Nozzle map (community): 1 and 5 = Butadiene; 2 and 4 = Styrene; 3 = Acrylonitrile.
  3. Place the cup under each nozzle, then dispense in order: 4, 3, 1, 4.
  4. Process the mixture. Wrong order → restart; right nozzle but empty cup → reposition the cup under the outlet.

Floppy disk doors — dial targets

Solution — door 1 & door 2
  1. Door 1: four dials in 90° steps (up / right / down / left). Reader calls orientations from their screen; operator stops each dial. Lights: orange unset, yellow setting, blue-white locked. Allow brief drift after release.
  2. Door 2: four dials in 45° steps (includes diagonals). Read this door’s display — door 1’s combo is not reused.
  3. If nothing opens from inside the printer route: size-swap — leave, get enlarged, partner shrinks and uses the outside console that starts the spinning-dial sequence for floppy 01.

3D printer 4×4 grid — read rule (random)

The lit pattern rerolls every attempt. There is no universal grid answer. Sources: weki 3D Printer Grid, Craft & Quest, Indie Walkthrough.

Solution — how to read and enter the grid
  1. After both floppy doors, the cabinet shows a 4×4 pattern: one lit column per row (random).
  2. Miniature explorer uses floor plates: Up / Down / Left / Right / Confirm. Cursor starts top-left.
  3. Partner reads column numbers top → bottom (columns 1–4 left → right). Operator moves the cursor to that cell and Confirms; each row keeps only one toggled cell.
  4. When all four rows match the cabinet, the printer outputs the green key card.
  5. Do not copy a screenshot grid from another run — wait for your cabinet lights.
Hint

Resin is the only fixed numeric sequence here. Floppy = call the live screen. Printer = copy today’s lights one row at a time.

Sources / Last verified: . Resin 4-3-1-4: wewereheretomorrow.net floppy/resin; guide.wiki Ch.1–2; weki Experimental Resin Notes. Printer rule: weki 3D Printer Grid; Craft & Quest.

Frequently asked questions

What is the resin nozzle order?

4 → 3 → 1 → 4 (Styrene, Acrylonitrile, Butadiene, Styrene).

Is the 3D printer grid always the same?

No. Copy the lit cabinet pattern for your current attempt; do not reuse another run’s grid.